I get asked a lot about this recipe, and for good reason. It’s pretty indistinguishable from the best cone 10 recipes out there. For those purists out there, I’m referring to Pinnell Clear, Deller Chun, Cushing’s LungChun, and any number of Robert Tichane’s recipes from his book Celadon Blues. In any event, I often point people to an older post, but in the years since I mistakenly transcribed a recipe wrong and happened on the winning formula, I’ve learned quite a bit working with this glaze; Things like it working reasonably well in soda and atmospheric kilns, looking very nice from a range of cone 5 to cone 12, and readily taking most mason stains.
Fiske 6/10 Clear Base:
F4 (Or MinSpar) Feldspar 34.9
Zinc Oxide 11
OM4 Ball Clay 13.8
(Pictured: Add 1.75% Robin’s Egg Blue Mason Stain)
Notes on materials, mixing, and application:
Feldspar:Since F4 is no longer widely available, Minspar 200 will work. Custer works as well, but the bubble matrix that really gives this glaze it’s character is different with custer, g200 (now g200hp), or nepheline syenite. Experiment first, because milage may vary. Of the ingredients, this is probably the 3rd most important.
Fluxes: Whiting and Zinc. This glaze is not kind to kiln elements. (See my post on zinc for clarification!) It’s my opinion that the relatively high % of zinc is caustic to electric kiln elements. If you must, ventilate the kiln, but expect a short life on the elements. Sometime in the near future I’ll be eliminating zinc and trying to use a frit to solve this, but until then I can only recommend firing in a gas kiln. It’s the cost of firing.
Clay: Probably the most important element of this recipe. When I was testing for cone 6 glazes, I made a mistake transcribing to a batch recipe. The result was that I had doubled the clay. After the firing I went back over the notes and realized why the glaze looked the way it did. One of the side effects of the higher clay content is that application is sometimes difficult. The higher % of clay makes thick applications crawl. To get around this I calcine 10 of the 15%.
Thus, my recipe looks like this:
Fiske 6/10 Clear Base: Minspar200 Feldspar 38, Whiting 14, Zinc Oxide 12, Calcined OM4 Ball Clay 10, OM4 Ball Clay 5, Silica 30. [H20 60%]
Silica: I use 200mesh sil-co-sil. I’ve tried 325 mesh, but it didn’t look right.
Colors/Mason Stains: I use Robin’s Egg Blue, Bermuda Green, and Canary yellow. Most colors I’ve tested, and usually 1.5-3% is pretty nice, but some take as much as 5-10%. I haven’t had much luck with purples, Pinks, and oranges, (they don’t play nice with the zinc) but honestly I’m largely done tweaking this one and haven’t tried in earnest to figure out those other colors. Metallic oxides will also work, cobalt at like .3% for a not overpowered blue color.
Application: Can’t stress this enough. It’s gotta be thick. I tell people to glaze “Thicker than you think thick is, and then just a little thicker.” I’ve taken to adding just a touch of deflocculent to the glaze batch so that it needs less water to become liquid. I then add a bit of Epsom salt to thicken the batch up. Again, this is to taste. Dipping is absolutely the way to go with this one, but I’ve gotten accustomed to spraying it. Usually takes about 15 minutes to spray glaze something appropriately.
Firing: As I mentioned earlier, it’s got a pretty wide range. It will be fully melted, albeit slightly pin holed at cone 5. Ideally, I like to go to a perfect 6, but taking it to 7 or programming a hold in the schedule makes for some nice movement that suits carving and texture very well. Most of my work is completely smooth, so I prefer it to stay thick and not run down too much. It takes some getting used to, but when you do, it behaves very predictably. It can also go into reduction, but the colors change quite a bit. Less change with Bermuda Green, but quite a bit with the Robin Egg Blue. Its been fired every which way, and needs to be tested before full comittment.